Prescription Google Glass – Round 2

By Josh Highland in Google Glass, hacks, hardware, Tech

JoshHighland-Google-Glass-Prescription-Lenses-Round2

Last month I modified my Google Glass to work with my prescription lenses. It was better but there was still room for improvement. Some of the problems I had:

  • The zip tie was tight but, the shortened arm of my eye glasses could slip out. A few times I took my glass out of my bag and it had come undone
  • The zip tie allowed the for glass to pivot up and down. This made it difficult to keep the Glass optic aligned if I was doing anything active.
  • It looked weird – I had a zip tie holding everything together!

I decided that something had to be done. After some thought, I realized that shrink tubing my be the answer.

Positives to shrink tubing:

  • More surface area connecting the Glass to the frames = more stability, less vertical wiggle.
  • Less likely to come apart
  • Still a semi-permanent non-destructive solution – I could always put it back to the default factory configuration.
  • Better looking – no more zip tie, very little bulk

Negatives to shrink tubing:

  • Less room to adjust the alignment of Glass
  • Using a heat gun on the sensitive Glass – could melt / damage them

After weighing out the pros and cons I decided to go for it!

I assembled my tools. Shrink tubing, a heat gun, scissors, an exacto knife, and my Glass / Glasses creation.

 

1-theTools

I started by cutting off the zip tie that has holding it all together.

2-tearDown

Next I cut the shrink tubing to length. I had to be able to reach all the inputs on the Glass – the power button, USB port and camera trigger.

3-cuttingTubing

Next I had to stretch the tubing a bit. Out of the package, it was too small to fit over the optic. I places the tube onto the scissors and opened them, stretching the tube wider.

4-tubeStretching

Once stretched, I slid the tube over the optic and onto the arm of Glass.

5-overTheOptic

Paying close attention, I made sure that the tube was ale to clear the USB port, camera trigger and power button.

6-cameraBotton

7-usbPort

8-powerButton

Once I got everything where I wanted it and aligned, I used a zip tie to hold it in place. I plugged an old USB cable into the port in an attempt to protect it a little bit during the heat shrink process.

9-glassFit

I decided to wrap as much of the Glass as I could into a heavy rag to protect it from some of the heat during the heat shrink process.

10-readyToShrink

It didn’t take long for the heat gun to get hot. I slowly ran the gun over the tube, shrinking it to fit, being careful to not get anything too hot. This was a nerve wracking experience. I needed to shrink the tube, but not damage the Glass. It was a balancing act.

11-shrunk

I let the tubing cool down before I remove the zip tie and unplugging the USB cord. I was very happy with the end results. The tube had shrank down, firmly sandwiching the Glass to the frame of my prescription glasses.

11-shrunkCleanUp

Glass powered up with no problem. I hadn’t killed them! To my surprise, touches worked through the plastic tubing! Bonus win!

12-bootup

I opened up the “MyGlass” app on my Nexus 7 – Bluetooth and Wifi were still working.

13-nexusTest

I also tested the USB port for charging and data transfer. Both tests worked. Next was taking pictures and video. Both of those passed as well. I had done it.

14-done

The end result is a clean and nearly invisible fusion of my Google Glass and my prescription eye glasses.

15-done

16-done

17-done

This is the first time that I truly feel that Glass fits me properly. This is a game changer.

I know that Google is working on prescription Google Glass, and I really hope that I’m part of that pilot program. Until then, I plan on pushing the limits of Glass. I’m a member of the “Google Glass Explorer Program”, explorers take risks and discover new things. That’s what I’m trying to do.

18-BW_trial

19-JoshHighlandGoogleGlasses

I have a feeling that this won’t be my last mod to Glass. I have more ideas but they start getting into the destructive realm and I’m not sure if I’m willing to go down that one way path. Time will tell.

 

Google Glass Prescription Lenses

By Josh Highland in Google Glass, hardware, Josh's Rambling, Tech

Josh Highland Google Glass Prescription Lenses

Update – I’ve hacked them once again!

Before I picked up my Google Glass, I knew they didn’t support prescription lenses. To prepare for the Google Glass, I went to my optometrist and got fitted for contact lenses. She tried to talk me out of getting contacts due to the shape of my right eye (severe astigmatism). She explained that contacts would most likely not be comfortable and to stick to glasses. Knowing that Google Glass didn’t support prescription lenses, I got contacts anyways. I should have listened to the doctor, the contacts were HORRIBLE! I immediately switched back to my Warby Parker eye glasses for daily wear.

I tired to wear my Google Glass with my eye glasses, but there was no way to make it work. Luckily I can see pretty good up close, so I was able to wear my Google Glass by themselves. There was no way that I could drive a car, work on a computer, or carry on daily life without my eye glasses, so my Google Glass had remained somewhat of a novelty. I would take off my eye glasses, put on my Google Glass and show people the future, but as soon as the demo is over I take the Glass off and put my eye glasses back on.

Today I realized that I hadn’t really worn my Google Glass in a few days. It really upset me. I want Glass to be a part of my daily life, but without support for prescription lenses, it wasn’t going to happen. I decided to do something about it. I was willing to take apart my Google Glass if I had to. I was going to make them work with my prescription lenses at any cost.

I started by removing the only exposed screw on the Google Glass. It’s located just above the right temple, and can be removed with a Torx-5 bit. After loosing the screw, the titanium headband is easily detached, leaving the main Glass unit.

IMG_0736IMG_0738-1IMG_0739Looking at my options, I took and old pair of my 141 eye wear and decided to cut the right arm. I used a pair of wire cutters to get the job done. After my first cut, I realized that I was going to need to cut it a bit shorter, so that the power button for the Glass was exposed.IMG_0740IMG_0741-1IMG_0743-1With the arm at a minimal length, I was left to figure out how to attach the Glass to my glasses. I first tried double stick tape, but it just wasn’t strong enough. I didn’t want to use glue and risk damaging the plastic housing. Instead of getting fancy, I went with a very cheap, low tech solution – a zip tie, or wire tie. I just happened to have a black one in my tool box.

After snugging down the zip tie and cutting off the excess, the whole assembly felt very solid and fit very well. The side of Google Glass is touch sensitive but the tie doesn’t seem to interfere with  it’s responsiveness.IMG_0744-1IMG_0748-1IMG_0749-1For the first time, I was able to see Glass through my prescription lenses. I could truly appreciate the quality of the display optic. Images were more vibrant and clear. This is the experience I was looking for from the beginning. This is going to let me wear Glass on a daily basis, and it cost me less than $0.01 to do it! I may try to use a thinner zip tie so its not so obvious. Then again, I have a computer hanging off my face and I think that most of the attention will be focused on it. IMG_0750-1IMG_0751-1Maybe Google feels that the people who have the Glass Explorer Editions are true explorers and pioneers, and they will find a way to make prescription lenses work. Maybe Google hasn’t found a good way to make lenses work for most people. All I know is that I have found a way to make Glass work for me, and this is the start of something awesome. Look out world!

IMG_0755-1IMG_0757-1

141 Eyewear, a product with a purpose

By Josh Highland in Josh's Rambling

Over the past few years, Tom’s shoes have become well known, hip and trendy. Everyone knows that if you buy a pair of their shoes, they donate a pair of shoes to children in need. I love the philosophy, but HATE their shoes. Personally, I think they look ugly and clunky, but to each their own. Don’t worry, I’m not a hater, my wife has several pairs.

A few weeks ago, I saw a tweet from Timothy Ferriss about products with a purpose, and I followed the link. I don’t remember the article that I was linked to, but I managed to end up on 141Eyewear.com.

141 Eyewear is a company that helps children in need, who have eye problems. When you buy a pair of frames, they give a pair of glasses (including the eye exam and corrective lenses) to children in need, one for one, as their name implies. As someone who wears depends on eye glasses, and know how important is is to have the proper prescription, plus, who doesn’t like helping out kids in need? It’s a win win situation.

I had been thinking about getting a new pair of glasses for the last few months, but I’m very picky about my frames. I was instantly excited when I saw the awesome frames that 141 Eyewear produces. I saw the “Davis” frames, and knew that I had to have a pair.

I combed through the 141 website but couldn’t find a place to purchase a pair, so I used their contact form to ask them where I could buy a pair. I also hit them up on their twitter accout. Kyle Yamaguchi, one of the founds of 141 Eyewear instantly got back to me and told me that their eye wear was only being sold in Portland Oregon until summer time 2010. I was bummed to hear this, but it just so happened that a week earlier I had bought plane tickets to visit Portland with my wife.

When we landed in Portland, I sent a tweet telling people I was in Portland, and asked advise on what to check out. To my surprise, Kyle Yamaguchi was one of the first people to give me some suggestions. He also gave me the address of a store that carries 141 Eyewear.

We wandered around Portland for a few days, and eventually made it to the Pearl District, and “The Eye Studio“, a hip looking shop that carried lots of designer frames.

We were instantly greeted by the friendly staff at The Eye Studio, and shown the 141 Eyewear collection. I was in luck, they had one pair of “Davis” frames in stock. I tried them on and was instantly pleased with them.  The photos online didn’t do it justice, the finish on the “noir” version of the Davis frames is matte black and sleek. I had to have them.

While my wife, Amy, was trying on some frames, Shu-Chu Wu, also a founder of 141 Eyewear, came out of the back room and greeted us. She was super nice and showed us some photos of an eye clinic that 141 had put on. The kids looked amped in their new glasses.

After a bit of hangout, I bought the frames, and we were on our way. I didn’t get my prescription filled, so the frames are still empty. I figured I’d wait until I got home to Southern California.

I don’t publicly endorse many products, but I fully back 141 Eyewear and I hope you do to. They made great products that look great, and are helping kids at the same time. After having contact with both of the founders of the company, and seeing the work they have already done, I can tell that their motives are good and their intentions pure.

I’ll be posting a pic of myself wearing my 141 Eyewear once I get the lenses put into the frames next week.